Easytop concealed free-flow valve with SC-Contur
Product information
Easytop concealed free-flow valve with SC‑Contur
for potable water installation
| Year built (from): | 2017-04-01 |
Trade mark rights exist for this document; for further information, go to viega.com/legal .
Target groups
The information in this manual is directed at heating and sanitary professionals and trained personnel.
Individuals without the abovementioned training or qualification are not permitted to mount, install and, if required, maintain this product. This restriction does not extend to possible operating instructions.
The installation of Viega products must take place in accordance with the general rules of engineering and the Viega instructions for use.
Labelling of notes
Warning and advisory texts are set aside from the remainder of the text and are labelled with the relevant pictographs.
DANGER!
This symbol warns of possible life-threatening injury.
WARNING!
This symbol warns of possible serious injury.
CAUTION!
This symbol warns of possible injury.
NOTICE!
This symbol warns of possible damage to property.
INFO!
This symbol gives additional information and hints.
About this translated version
This instruction for use contains important information about the choice of product or system, assembly and commissioning as well as intended use and, if required, maintenance measures. The information about the products, their properties and application technology are based on the current standards in Europe (e. g. EN) and/or in Germany (e. g. DIN/DVGW).
Some passages in the text may refer to technical codes in Europe/Germany. These should serve as recommendations in the absence of corresponding national regulations. The relevant national laws, standards, regulations, directives and other technical provisions take priority over the German/European directives specified in this manual: The information herein is not binding for other countries and regions; as said above, they should be understood as a recommendation.
Standards and regulations
The following standards and regulations apply to Germany / Europe and are provided as a support feature.
Regulations from section: Fields of application
Scope / Notice | Regulations applicable in Germany |
|---|---|
Planning, execution, operation and maintenance of potable water installations | DIN EN 806, part 1 |
Planning, execution, operation and maintenance of potable water installations | DIN EN 806, part 2 |
Planning, execution, operation and maintenance of potable water installations | DIN EN 806, part 3 |
Planning, execution, operation and maintenance of potable water installations | DIN EN 806, part 4 |
Planning, execution, operation and maintenance of potable water installations | DIN EN 806, part 5 |
Planning, execution, operation and maintenance of potable water installations | DIN EN 1717 |
Planning, execution, operation and maintenance of potable water installations | DIN 1988 |
Planning, execution, operation and maintenance of potable water installations | VDI/DVGW 6023 |
Planning, execution, operation and maintenance of potable water installations | Trinkwasserverordnung (TrinkwV) |
Regulations from section: Media
Scope / Notice | Regulations applicable in Germany |
|---|---|
Suitability for drinking water | Trinkwasserverordnung (TrinkwV) |
Regulations from section: Product description
Scope / Notice | Regulations applicable in Germany |
|---|---|
Suitability for drinking water installations | Trinkwasserverordnung (TrinkwV) |
Suitability for drinking water installations | DIN 50930‑6 |
Requirements in plastic components in drinking water installations | DVGW-Arbeitsblatt W270 |
Regulations from section: Overview
Scope / Notice | Regulations applicable in Germany |
|---|---|
Compliance with the inspection requirements (fittings group I) | DIN EN 13828 |
Compliance with the inspection requirements (fittings group I) | DIN EN 1213 |
Regulations from section: Marking on components
Scope / Notice | Regulations applicable in Germany |
|---|---|
Designation noise class I | DIN EN 1213 DIN EN 13828 |
Regulations from section: Compatible components
Scope / Notice | Regulations applicable in Germany |
|---|---|
Permitted pipe types | DVGW-Arbeitsblatt W 534 |
Permitted copper pipes | DVGW-Arbeitsblatt GW 392 |
Permitted copper pipes | DIN EN 1057 |
Permitted stainless steel pipes | DVGW-Arbeitsblatt GW 541 |
Permitted stainless steel pipes | DIN EN 10312 |
Permitted stainless steel pipes | DIN EN 10088 |
Regulations from section: Corrosion
Scope / Notice | Regulations applicable in Germany |
|---|---|
External corrosion protection | DIN EN 806‑2 |
External corrosion protection | DIN 1988‑200 |
External corrosion protection | DKI-Informationsdruck i. 160 |
Regulations from section: Leakage test
Scope / Notice | Regulations applicable in Germany |
|---|---|
Leakage test for potable water installations | DIN EN 806, part 4 |
Leakage test for potable water installations | ZVSHK-Merkblatt |
Regulations from section: Maintenance
Scope / Notice | Regulations applicable in Germany |
|---|---|
Operation and maintenance of potable water installations | DIN EN 806‑5 |
Intended use
INFO!
Coordinate the use of the model for areas of use and media other than those described with the Viega Service Center.
Areas of use
Use is possible in the following areas among others:
Drinking water installations
Industrial units
The model serves as a shut-off for the storey units.
The general rules of engineering and the applicable regulations must be observed for planning, execution, operation and maintenance potable water installations, see Regulations from section: Fields of application .
Media
The model is also suitable for the following media, amongst others:
Drinking water without limitations acc. to the applicable directives, see Regulations from section: Media
maximum chloride concentration 250 mg/l pursuant to applicable regulations, see Regulations from section: Media
Product description
According to the applicable regulations, Easytop system fittings can be used for all types of potable water and are DVGW certified, see Regulations from section: Product description . Their plastic components comply with the KTW recommendation and the requirements pursuant to the applicable regulations.
Overview
INFO!
The Easytop system fittings comply with the test requirements specified in the applicable regulations, see Regulations from section: Overview Sound protection Lap≤ 20 dB(A)
- 1 - Easytop concealed free-flow valve
- 2 - shut-off units and seals made of EPDM
- 3 - valve top (dead space free)
- 4 - protective sleeve
- 5 - driver
- 6 - Protective cap
The model is equipped as follows:
valve casing and top made of gunmetal/silicon bronze
Site protection
dual-sided press connection with SC‑Contur
sealing elements made of EPDM
green dot for potable water
The model is available in the following dimensions: d 15 / 18 / 22.
Press connection with SC-Contur
The press connection has a circumferential bead in which the sealing element lies. The connector is deformed upstream and downstream of the bead and permanently connected to the pipe during pressing. The sealing element is not deformed during pressing.
SC‑Contur
Viega press connections are equipped with the SC‑Contur. The SC‑Contur is a safety technology that is certified by the DVGW and ensures that the connection is guaranteed to be leaky in an unpressed state. In this way, unpressed connections are noticed immediately during a leakage test.
Viega guarantees that unpressed connections are visible during a leakage test:
with wet leakage test in the pressure range from 0.1 hPa–0.65 MPa (1.0 mbar–6.5 bar)
with dry leakage test in the pressure range from 22 hPa–0.3 MPa (22 mbar–3.0 bar)
Sealing elements
Area of use of the EPDM sealing element
NOTICE!
Only EPDM sealing elements are approved in potable water installations. The use of other sealing elements is not permitted.
The model is factory-fitted with EPDM sealing elements.
Area of use |
|---|
Use |
Operating temperature [Tmax.] |
Operating pressure [Pmax] |
Comments |
Potable water |
|---|
all pipeline sections |
90 °C |
1.6 MPa (16 bar) |
see notes Media |
Markings on components
The press connections are marked with a coloured dot. This identifies the SC‑Contur, where the test medium would escape in the case of an inadvertently unpressed connection.
The model is marked as follows:
flow direction indicator
noise class I on the basis of applicable regulations, see Regulations from section: Marking on components
dimension
DVGW writing
green dot for potable water
position indicator
Compatible components
The model is equipped with press connections and compatible with the Profipress, Sanpress and Sanpress Inox system.
Pipes
The press connections are tested and approved according to the applicable regulations with the following pipe types:
Copper pipes
Stainless steel pipes (material 1.4401 / 1.4521)
Technical data
Observe the following operating conditions for the installation of the model:
Operating temperature [Tmax] |
|---|
Operating pressure [Pmax] |
90 °C |
1.0 MPa (10 bar) |
Information for use
Corrosion
Overground pipelines and fittings in rooms do not normally require external corrosion protection.
There are exceptions in the following cases:
Contact with aggressive building materials such as nitrite or materials containing ammonium
in aggressive surroundings
If external corrosion protection is required, observe the pertinent guidelines, see Regulations from section: Corrosion .
INFO!
Easytop fittings made of gunmetal/silicon bronze are suitable for all types of potable water.
The chloride concentration in the medium must not exceed a maximum value of 250 mg/l.
This chloride is not a disinfectant, but in fact pertains to the content in sea and table salt (sodium chloride).
Optional accessories
The following optional accessories are available:
Insulating shell
Equipment sets
Public building model
Mounting sets
Handling
Assembly information
Installation dimensions
- A - at least 45 mm
- B - maximum 130 mm
(when using model 2236 maximum 80 mm)
Permitted exchange of sealing elements
INFO!
Important instruction
With their material-specific qualities, sealing elements in press connectors are adapted for use with the corresponding media and/or the areas of use of the piping systems and are generally only certified for them.
The exchange of a sealing element is generally permitted. The sealing element must be exchanged for a designated spare part for the intended application Sealing elements . The use of other sealing elements is not permitted.
Mounting instructions
Checking system components
INFO!
Do not remove the model from the packaging until immediately before use.
System components may, in some cases, become damaged through transportation and storage.
Check all parts.
Replace damaged components.
Do not repair damaged components.
Contaminated components may not be installed.
During assembly
Observe the following when mounting:
minimum / maximum installation depth
use suitable tools
INFO!
Choose the place of installation so that the fitting is easily accessible, simple to operate and the insulating shell can be well mounted.
Laying and fixing pipes
For information, refer to the instructions for use of the Profipress, Sanpress and Sanpress Inox systems.
Length expansion
For information, refer to the instructions for use of the Profipress, Sanpress and Sanpress Inox systems.
Required tools
The following tools are required for production of a press connection:
pipe cutter or a fine-toothed hacksaw
deburrer and coloured pen for marking
press machine with constant pressing force
Press jaw or press ring with corresponding hinged adapter jaw, suitable for the pipe diameter and suitable profile
Recommended Viega press machines:
Pressgun 5
Pressgun Picco
Pressgun 4E / 4B
Picco
Type PT3-AH
Type PT3-H / EH
Type 2 (PT2)
Assembly
Replacing the sealing element
Removing the sealing element
INFO!
Do not use pointed or sharp-edged objects to remove the sealing element. These could damage the sealing element or bead.
-
Remove the sealing element from the bead.
Inserting the sealing element
-
Insert a new, undamaged sealing element into the bead.
-
Ensure that the complete sealing element is in the bead.
Shortening the pipes
NOTICE!
Leaky press connections due to damaged material!
Press connections can become leaky due to damaged pipes or sealing elements.
Observe the following instructions to avoid damage to pipes and sealing elements:
Do not use cutting discs (angle grinders) or flame cutters when cutting to length.
Do not use grease or oils (e. g. cutting oil).
For information about tools, also see Required tools .
-
Cut the pipe properly using a pipe cutter or fine-toothed hacksaw.
Avoid grooves on the pipe surface.
Pressing the connection
NOTICE!
Leaky press connections due to pipes being too short
If two press connectors are to be mounted onto a pipe without an interval, the pipe must not be too short. If the pipe is not inserted up to the prescribed insertion depth in the press connector during pressing, the connection may become leaky.
With pipes with a diameter of d 15–28 mm, the length of the pipe must be at least as long as the total insertion depth of both press connectors.
Requirements:
The pipe end is not bent or damaged.
The pipe is deburred.
The correct sealing element is in the press connector.
EPDM = polished black
The sealing element is undamaged.
The complete sealing element is in the bead.
-
Push the press connector onto the pipe as far as it will go.
-
Mark the insertion depth.
-
Place the press jaw onto the press machine and push the retaining bolt in until it clicks into place.
INFO!Observe the press tool instruction manual.
-
Open the press jaw and place at a right-angle onto the connector.
-
Check the insertion depth using the marking.
-
Ensure that the press jaw is placed centrally on the bead of the press connector.
-
Carry out the pressing process.
-
Open and remove the press jaw.
-
Connection is pressed.
Mounting the valve
INFO!
Carry out a functionality test after initial mounting.
Installation is possible in masonry (wet construction) and in dry constructions (pre-wall / duct installations).
Attaching in dry constructions
-
Attach the fitting from behind with the fixing set onto a Viega fitting holder with slot nuts.
-
Seal the wall lead-in on the front side of the wall with the self-adhesive sealing flange.
-
Attach the protective sleeve of the valve in front of and behind the cladding (e. g. sheetrock or Fermacell panels) with lock nuts.
-
Seal the wall lead-in on the front side of the wall with the self-adhesive sealing flange.
Actuating the valve
-
Open or close the valve with a ¼ turn.
-
During the preliminary building work phases:
Actuate the valve via the protective cap.
Leakage test
The installer must perform a leakage test before commissioning.
Carry out this test on a system that is finished but not yet covered.
Comply with the general rules of engineering and the applicable directives, see Regulations from section: Leakage test .
Document the result.
Maintenance
NOTICE!
Inform your customer or the operator of the drinking water installation that the system has to be maintained on a regular basis.
Observe the applicable regulations for the operation and maintenance of drinking water installations, see Regulations from section: Maintenance .
INFO!
Viega recommends actuating the fitting regularly and checking its function.
Disposal
Separate the product and packaging materials (e. g. paper, metal, plastic or non-ferrous metals) and dispose of in accordance with valid national legal requirements.